Pay Attention
All the pictures in this instruction are for reference only.Pictures and objects may be a little bit different,But the installation method is the same.
To facilitate your installation, please read the instructions carefully before installation.Take care to protect the surface of your car when you install it,Avoid scraping.
Please check regularly whether all the fittings connected with the vehicle are loose.To ensure safe use.
Installation Steps
Check the accessories list and accessories chart to see if the accessories are complete,After completion of car tail door installation,Please long press the tail door to install the switch button,In 3-5 seconds the "beep" has a long sound. Let the handle loose and press the end door. There is two “beep”, that is, the tail gate is completed.
Safety protection measures and tools for pre-installation parts preparation(check the completeness of the accessories),Before loading the car, a layer of cloth is laid on the rear door of the car. Prevent the scraping of the body,Take out the product and install the tool.
1.Remove the tailgate trim and the original car stay
2.Remove the right upper bracket of the original car, install the upper right bracket of our company, and fix it with our screws.
3.Remove the lower right ball of the original car, install the lower right ball of our company and add a gasket to the bottom of our company.
4.Install the struts (the same steps)
5.Remove the left upper bracket of the original car, install the left upper bracket of our company, and fix it with our screws.
6.Remove the original car ball head, install our ball head and add a gasket to our bottom
7.Punch the hole at the upper bracket as shown in the figure, the Hall wire passes through the rubber plug of the hole card
8.Hall line trace to the tailgate cover
9.Remove the trim panel under the main driver and find the power supply
10.Unplug the original car 30A fuse
11.Plug in our power plug
12.Find the ground wire at the bottom right of the power supply and connect the ground wire.
13.Unplug the rubber plug at the main driving sliding door and find the central control line.
14.Our yellow central control line is connected to this seat white line (from the left to the right, the first row of the seventh hole)
15.Main drive front switch button
16.Find the original seat and grounding screw at the back door
17.Two lines pulled out by the front switch, one connected to the brown line and one grounded line
18.Unplug this seat at the tailgate lock and insert it into our three-way socket.
19.Remove the original car screws, remove the original car suction lock, install our electric suction, fix with the original car screws
20.Insert the electric suction socket on our company as shown in the figure.
21.Punch the removed plaque, install our tailgate switch, restore all plaques
After the installation is complete, please must learn to tail gate Settings, please make sure that the door can switch in place (the tail gate to ideal height, push the tail gate equipped with switch, 3-5 seconds long rang hear "di", release your hand, and then click on the end closed door keys, the tail door locked in place, and then hear the "click" sound, the tail door of learning is complete, if not hear "di di" sound, learning is not successful, need to learn;If do not close the door, in the study with the hand to assist the door closed)
Disclaimer
The related problems and losses caused by improper installation and use are not covered by our company's warranty.Thank you for buying the intelligent electric lifting door. Please read this manual carefully before use, and collect carefully after reading, so that you can refer to it later.
Key control mode
1: open and close the door for three seconds by long pressing the rear door button of the original vehicle remote control
2: push the button once to open and close the door.
Set the height
Raise the tail door to the ideal height, press the tail door to add the switch button, 3-5 seconds hear "di" a long ring, release the handle, press the tail door button to close the door, and then hear "di" two, that is, the tail door learning completed
Attention!!!After setting the ideal height do not close the door by hand, do use the tailgate button we match
Contact Person: Mr. Carroll Chan
Tel: 13532848886
Fax: 86-0769-82198610