Plug & Play Power Tailgate Lift Kit with Anti-Pinch and Kick Sensor Electric Tailgate Lift for Mitsubishi Destinator 2026+
power tailgate lift kit voxy noah
,double suction lock tailgate
,kick sensor hands free liftgate
Basic Properties
Trading Properties
Few daily routines expose the shortcomings of a stock MPV faster than loading luggage into the back of a Mitsubishi Destinator. The factory hatch is heavy, the handle sits high, and both hands are usually occupied with bags. The KMYL989 automatic tailgate lift kit solves that problem at its root. Two Hall-sensor electric struts, a double suction lock and a dedicated ECU control box replace the manual gas struts, giving the rear door full power operation from the remote key, the dashboard switch, the tailgate button or a light kick beneath the bumper. Nothing about the vehicle layout has to be cut, welded or drilled beyond the original fixing points, so the conversion stays fully reversible.
The kit was developed specifically for the 2026+ Mitsubishi Destinator body, which means the strut length, the latch geometry and the linkage travel all match the original hardware instead of being adapted from a universal design. The result is a quieter, faster and far more predictable door cycle, with a consistent soft-close finish on every stroke.

- Double suction lock closing: the latch pulls the hatch in electrically once the panel reaches the final few millimetres, so the door never needs to be slammed and the rubber weather seal keeps its shape over years of use.
- Kick sensor opening: a foot gesture below the rear bumper releases the latch and lifts the door, which is a decisive advantage when both hands carry luggage, samples or a child seat.
- Adjustable anti-pinch protection: current monitoring on both struts stops and reverses the door the moment resistance is detected, and the trigger force can be tuned to the owner's preference through the control box.
- Balanced twin-strut drive: load is shared evenly between the two actuators, keeping panel alignment stable even if one actuator is unplugged during service.
- Height memory: the maximum opening point is stored by button command, which keeps the hatch clear of low garage ceilings and car park pipes.
- Four-channel control: remote key, cabin switch, tailgate button and kick sensor all feed the same ECU, and manual movement stays light and smooth if the owner prefers to operate the door by hand.

- The owner sends an open command from the key fob, the cabin switch or a kick gesture under the bumper.
- The ECU releases the double suction lock and drives both struts upward with a soft-start ramp, so the panel accelerates gently.
- A Hall sensor counts motor rotation continuously, letting the ECU stop exactly at the memorised height.
- On closing, the struts decelerate before contact and the lock motor pulls the panel into the final seat position.

| Parameter | Specification |
|---|---|
| Vehicle application | Mitsubishi Destinator 2026+ |
| Model number | KMYL989 |
| Lock configuration | Double suction lock, latch and upper bracket included |
| Drive unit | Two electric struts with built-in Hall sensors |
| Control unit | Dedicated ECU control box with sealed harness |
| Rated voltage | 12V DC, operating range 9V–16V |
| Opening methods | Remote key, cabin switch, tailgate button, kick sensor |
| Safety functions | Anti-pinch, overcurrent cut-off, low voltage alarm, fault recovery |
| Height memory | Programmable maximum opening position |
| Finish | Gold anodised strut body, zinc plated brackets |
| Certification | RoHS, E-mark E24 |
| Warranty | 12 months against manufacturing defects |

The conversion targets private Mitsubishi Destinator owners who use the vehicle as a family shuttle, plus fleet operators running airport transfers and hotel pickups where drivers open the boot dozens of times a day. Because the kick sensor works through the bumper skin, taxi and chauffeur operators can load luggage in rain without putting bags down on wet ground. Workshops and accessory distributors also stock the kit as a fixed installation package, since the harness is pre-terminated and the fitting sequence follows the factory service manual layout.
Every set ships as one complete installation package: two electric struts, one double suction lock, one ECU control box, a plug-and-play wiring harness, mounting brackets, fixings and an illustrated instruction sheet. One set is packed in an inner box and four sets are consolidated into an export carton with foam separation. Each unit is cycled on a test bench before packing, and the recorded stroke count, current draw and latch pull force travel with the batch record. Shipment leaves the factory 3–5 working days after payment when stock is available, and 10–15 days for production orders.

