Home
Products
About Us
Factory Tour
Quality Control
Contact Us
Request A Quote
News
Company News
Dongguan Kaimiao Electronic Technology Co., Ltd
Home News

The Installation of Jeep Guide

China Dongguan Kaimiao Electronic Technology Co., Ltd certification
China Dongguan Kaimiao Electronic Technology Co., Ltd certification
Hello, Florence. We have tested one tailgate on Hyundai Tucson. We found that the product quality is good

—— Bolkar

they products are the best in the market we have used other company. there back up service is professiona.l

—— Mr. Nolan

I'm Online Chat Now
Company News
The Installation of Jeep Guide
Latest company news about The Installation of Jeep Guide

 

Attention

 

1. Before installing the tailgate, check the status of the original tailgate. (Whether the gap in the door is balanced)

 

2. All images in the manual are for reference only. Pictures may not be the same as the real one, but the installation method is the same.

 

3. In order to facilitate your installation, please ca refullyread the product manual before installation. Please pay attention to protect the surface of your car to avoids cratches. Please regularly check all parts connected withthe car for looseness, to ensure the safety of use.

 

4. After the tailgate is installed, must learn settings to openand close the door.

 

5. Raise the tailgate to the top, and then press the tailgate switch button for 3-5 seconds. When you hear a sound"Di——", loose your hand. Finally, press the tailgate switch button again, you will hear "DiDi——" when the door was closed. Setting finished. If you don't have hear"DiDi——", setting is not succeed and you need to set again.

 

Installation Instruction

 

1.Remove the plaque and the original car electric pole

 

latest company news about The Installation of Jeep Guide  0

 

2. Use the original car upper bracket to install our company electric pole

 

latest company news about The Installation of Jeep Guide  1

 

3.Remove the right lower bracket of the car and install the lower right bracket

 

latest company news about The Installation of Jeep Guide  2

 

4.Remove the left lower bracket of the original car and install the left lower bracket

 

latest company news about The Installation of Jeep Guide  3

 

5.The Holzer cable passes through this reserved hole as shown in the figure

 

latest company news about The Installation of Jeep Guide  4

 

6.Unscrew the panel under the main driver, find the power supply, remove the original car 20A fuse plug, plug our power plug

 

latest company news about The Installation of Jeep Guide  5

 

7.Earth wire connection

 

latest company news about The Installation of Jeep Guide  6  latest company news about The Installation of Jeep Guide  7

 

8.Plug the socket of our company into this hole, plug the other end into our agreement box

 

latest company news about The Installation of Jeep Guide  8

 

9.In the main driving position as shown in the figure, remove the plaque plate punching and installing the front switch button (put the 2p yellow wire from the protocol box to the front switch)

 

latest company news about The Installation of Jeep Guide  9

 

10.Connect the original vehicle unlocking line and the in-place line respectively to the unlocking line and the in-position line of our switch wiring harness (the follow-up is directly connected with the three-way adaptor socket provided by our company, avoiding the need for trimming)

 

latest company news about The Installation of Jeep Guide  10

 

11.Remove the original car lock, install our electric suction lock

 

latest company news about The Installation of Jeep Guide  11

 

12.Lock the lock rope on the motor, tighten the screws on both sides, and fix it with our screws and washers

 

latest company news about The Installation of Jeep Guide  12

 

13.Screw it back to original motor and tighten it with a wrench

 

latest company news about The Installation of Jeep Guide  13

 

14.Connect the plug of our electric suction line with the motor socket

 

latest company news about The Installation of Jeep Guide  14

 

15.Paste our 3M adhesive on the back of the motor

 

latest company news about The Installation of Jeep Guide  15

 

16.Motor installation position

 

latest company news about The Installation of Jeep Guide  16

 

17.Install the central control box of our company as shown in the figure, insert a pair of control boxes for the Holzer cable, power supply, and electric suction plug (put the yellow cable out of the protocol box and the yellow cable thrown out of the central control box)

 

latest company news about The Installation of Jeep Guide  17

 

18. Control box installation position

 

latest company news about The Installation of Jeep Guide  18

 

19.Punches at the tail door handle to install our switch button

 

latest company news about The Installation of Jeep Guide  19

 

20.After the installation is complete, you must set the tailgate learning. Make sure that the door can be turned on and off.

 

latest company news about The Installation of Jeep Guide  20

 

 

Pub Time : 2018-04-16 10:02:44 >> News list
Contact Details
Dongguan Kaimiao Electronic Technology Co., Ltd

Contact Person: Mr. Carroll Chan

Tel: 13532848886

Fax: 86-0769-82198610

Send your inquiry directly to us (0 / 3000)